SGE Kubaton economic tank for the transport of liquids
PLN345.63
tax incl
PLN281.00
tax excl
SG-100E
- Capacity from 100 to 200 l
- Monolithic construction for liquid transport
- Good price/quality ratio
Kubaton SGE economic tank for the transport of liquids
The tanks have the Polish Hygienic Certificate - PZH, which authorises them for contact with drinking water. The original document is available in the attachments.
The SGE series is an economical version of the liquid transport tank. It differs from the SKE version primarily in weight and dimensions. They are characterised by a very good price/quality ratio. However, both models are fully safe and durable. They are successfully used as transport tanks. Blue tanks are available. Other variants on individual enquiry.
The container is fully sealed. This is due to the tighter lid compared to other container series. The SGE therefore proves its worth as a container for transporting liquids. To avoid leakage, the container should be filled to a level 5% below its nominal volume. Blue and white containers are available. Other variants on enquiry.
Polyethylene tanks are intended for the purpose of storing and transporting water and other chemicals (table of chemical resistance). The containers are intended for storage at an ambient temperature of -40 to +60 (+/- 5) °C. It is recommended to limit sun exposure during storage. The heat and the influence of UV have a negative effect on the properties of some substances. It does not corrode and does not fade under the influence of UV. The tanks were made by rotomoulding. They do not have seams or welds.
The SGE series is an economical version of the liquid transport tank. It differs from the SKE version primarily in weight and dimensions. They are characterised by a very good price/quality ratio. However, both models are fully safe and durable. They are successfully used as transport tanks. Blue tanks are available. Other variants on individual enquiry.
The container is fully sealed. This is due to the tighter lid compared to other container series. The SGE therefore proves its worth as a container for transporting liquids. To avoid leakage, the container should be filled to a level 5% below its nominal volume. Blue and white containers are available. Other variants on enquiry.
Polyethylene tanks are intended for the purpose of storing and transporting water and other chemicals (table of chemical resistance). The containers are intended for storage at an ambient temperature of -40 to +60 (+/- 5) °C. It is recommended to limit sun exposure during storage. The heat and the influence of UV have a negative effect on the properties of some substances. It does not corrode and does not fade under the influence of UV. The tanks were made by rotomoulding. They do not have seams or welds.
The tanks have a shape that makes them easy to stack. They can be transported by any car, not exceeding the permissible load capacity. The strength of the tank is due to the reinforced walls (thicker than conventional horizontal tanks) and the shape. The tanks have special stiffeners (ribs) that act as partial breakwater baffles. This limits the movement of the liquid during transport. Transport is significantly safer, as the tank does not vibrate uncontrollably.
The tank may have two 3/4 inch threaded holes on the top and bottom. Attention! By default, no top tapped hole. It can be installed on individual customer orders (they are closed in their original state). The standard thread is not designed for the float valve. In order to install the valve, you will need to drill a hole in any other location on your own. You can drill the hole on a flat wall where its position will be optimal. The standard threads are only for the connection of a fitting or tap. The manufacturer's warranty is still valid if the customer installs his own holes. Please read the instructions.
It is also possible to retrofit the tank with male thread sealed pipe:
It is also possible to retrofit the tank with male thread sealed pipe:
- plastic in size: ½", ¾", 1", 1 ¼", 1 ½ ", 2",
- brass in size: ¾", 1", 1 ½ ", 2".
Technical data
Tank | Capacity [l] | Height [mm] | Lenght [mm] | Width [mm] | Thickness of the wall [mm] | Neck diameter [mm] | Thread [inch] |
SG-100E | 100 | 340 | 800 | 480 | 3,5 | 220 | 3/4 |
SG-200E | 200 | 505 | 1000 | 480 | 3,5 | 220 | 3/4 |
*Dimensions may differ slightly due to the production process. The measurement tolerance is 5-10 % from the nominal values in the table.
Specific References
- ean13
- 5905567314087